9 May SikaGrout® 1. 1/4. C onstruction. SikaGrout® SikaGrout® High Strength shrinkage compensated cementitious grout. Product. Specialist Construction Supplies for Repair, Maintenance, Building & Infrastructure. Sikagrout Data Sheet. Specification notes. Product: Sikagrout SikaGrout DIVISION 3 – CONCRETE. Section – Grouts. Part 1 – General. Summary. A. This specification describes the grouting of cavities, voids.
|Published (Last):||4 August 2018|
|PDF File Size:||1.35 Mb|
|ePub File Size:||10.25 Mb|
|Price:||Free* [*Free Regsitration Required]|
Push the anchor bolt into the hole and press it gently to the bottom, displacing the Sika Grout and filling the annulus around the bolt. Mechanical mixing is preferred for quantities greater than 1 sikagrout 212. The correct quantity of Sika Sikagrout 212 required to completely fill the annular gap between the bolt and the sides of the hole should be determined before installation is attempted.
Users should always refer to the most recent issue of the Technical Data Sheet for the product concerned, copies of which will be supplied on request, or can be accessed on the sikagrout 212 under www. Wash clothing before re-use.
Width of gap to be grouted in mm. In practice, the sikxgrout in materials, substrates and actual site conditions are such sikagrout 212 no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice sikagrout 212.
Collect in appropriate container. Concrete surfaces must be clean, sound and free from oil, grease, cement laitance and all loosely adhering particles. Approximate Flow Sikagrout 212 in cm. The Company reserves itself the right to change the formulation of Sika products if sikagrout 212 required by new research and development.
The quantity of aggregate added should not exceed sikagrout 212 1 part of aggregate to one 1 part of Sika Grout by weight. Ensure that sufficient grout is available to maintain the hydrostatic sikagrout 212 throughout the grouting operation until the grout level is above the bottom level of the base plate.
Uncured material iskagrout be removed with water.
sikagrout 212 Sika Grout can be used to fill voids up to mm in depth. Do sikagrout 212 commence fogging until initial set has been reached. Place Sika Grout within 30 minutes of mixing. Exercise care, as with handling any chemical construction product.
Place the pre-determined quantity sikagrout 212 Iskagrout Grout directly into the bolt hole. After establishing the consistency required, determine the water requirement per 25 kg bag see Table 2. Contact Sika for further health and safety information.
SikaGrout – Everbuild
Protect from direct sunlight. Concrete grey when mixed. Water Requirements for SikaGrout All orders are accepted subject to our current terms of sale and delivery which are available on request. The expansive properties sikagrout 212 Sika Sikagrout 212 will be severely reduced if heat is introduced to the mixed product via warm batching water, hot storage conditions of Sika Groutand high substrate and ambient temperatures.
Water Requirement per 25 kg bag in sikagrout 212. Volume Yield per 25 kg bag. For external applications, protect sikagrout 212 rain until initial sikagrut has been achieved. For the structural grouting of: Sika Grout is a one component, multi-purpose,freeflowing, expanding,cementitious grout.
Use either a slow speed drill set at – rpm with a clean, rust free, mixing paddle, standard mortar or concrete mixing equipment, or purpose built cement grout mixing equipment. A slight agitation of the bolt will assist the Sika Grout to fill the annulus evenly.
Remove any excess water just prior to placing sikagrout 212 grout.
Dispose of in accordance with local regulations. Remove affected sikagrout 212 to fresh air immediately and contact a physician.
DO not attempt to add additional Sika Grout with the bolt in place.