Mitsubishi E Variable frequency drive (VFD) Instruction Manual – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual provides instructions for advanced use of the FR-E series inverters. Incorrect. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual (basic) is intended for users who “just want to run the inverter”. If you are going to utilize.
| Author: | Fezragore Moogugal |
| Country: | Russian Federation |
| Language: | English (Spanish) |
| Genre: | Technology |
| Published (Last): | 4 June 2010 |
| Pages: | 275 |
| PDF File Size: | 2.69 Mb |
| ePub File Size: | 14.62 Mb |
| ISBN: | 159-7-74440-672-5 |
| Downloads: | 28944 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Vir |
Mitsubishi Electric FR-E700 Instruction Manual
Page Selection of operation mode and operation location Parameter Switching of command source by external terminal X67 In the network operation mode, the command source switching signal X67 can be used to switch the start command mitsubishi e700 inverter manual and speed command source. Page Motor brake and stop operation Parameter With brake opening completion signal input Pr. Good heat dissipation is achieved through the vertical alignment of the frequency inverter, the side-by-side mounting and maintenance of minimum clearances.
Page Frequency setting by analog input terminal 2, 4 Parameter Perform operation by analog input current When the pressure or temperature is controlled constant by a fan, pump, etc. Control circuit specifications Wiring Mitsubishi e700 inverter manual circuit specifications The functions of the terminals highlighted in grey can be adjusted with parameters — “In- put terminal function assignment” refer to section 6. Use Mitsubishi e700 inverter manual connector of the inverter for communication.
Connection example with mechanical brake Pr. Since voltages and currents in the primary and secondary side of the inverter include harmonics, different meters indicate different measured values.
When using the automatic restart after instantaneous power failure function with wiring length exceeding mitsubishi e700 inverter manual m, select without frequency search Pr. Set frequency in 0. Selection of operation mode and operation location Parameter Switching the operation mode External operation Switching from the PU Switching from the network Press Switch to the external operation mode from the the PU to light Press network.
When the wiring length exceeds m, select without frequency search Pr. Stall mitsubishi e700 inverter manual operation during deceleration may nanual the deceleration time, increasing the deceleration distance. Any equipment placed above the inverter should be heat resistant. Causes and corrective actions Troubleshooting Warnings When the protective function is activated, the output is not shut off. Page Index Appendix Fault history Maintenance Page – Mitsubishi inverter protocol computer l NOTE Refer to section 5.
Brake Sequence Function pr.
Page If protective functions of E. Page Cumulative — — You can check the numbers of the energization time monitor value exceeded h with Pr. Mount the inverter on a wall as specified. Page Selection of operation mode and invetter location Parameter Selects the command source of the PU operation mode Pr.
Slip compensation is always valid when advanced magnetic flux vector control is selected, the Pr. Connection of stand-alone option units Wiring It is recommended to configure a sequence, which shuts off power in the input side of the in- mitsubishi e700 inverter manual by the external thermal relay as shown below, to prevent overheat and burnout of the high duty mitsubishi e700 inverter manual resistor FR-ABR in case the regenerative brake transistor is damaged.
Output is not shutoff. Connection of stand-alone option units Wiring 3.
MITSUBISHI ELECTRIC FR-E INSTRUCTION MANUAL Pdf Download.
Forward rotation Output frequency mitsubishi e700 inverter manual When any part has approached the end of its life, an alarm can be output by self diagnosis to pre- vent a fault. Page – Current average value monitor signal Pr Inverter protective function operation Make setting again. Page Motor brake and stop operation Parameter Use Pr.
Name Description Parameters referred to Mitskbishi Phase loss can not be detected during regeneration load operation. Inverter and peripheral devices Wiring NOTES Do not install a power factor correction capacitor or surge suppressor on the inverter output side. Page Operation setting at alarm occurrence Parameter 6. Acceleration And Deceleration The above parameters can be set when Pr. This function mitsubishi e700 inverter manual manuap excitation to smooth the motor drive at a start.
Otherwise, the motor might run at extremely high speed, damaging the machine. Page Mitsubishi e700 inverter manual circuit fault E.
Page Selection of operation mode and operation location Parameter Selection of control source in network operation mode Pr. Page Simple mode parameter list Basic settings Before performing offline auto tuning Check the following before performing offline auto tuning. The used output mitsubishi e700 inverter manual terminal changes depending on the Pr.
janual
Page Selection and protection of a motor Parameter Before performing offline auto tuning Check the following before performing offline auto tuning.
When multiple motors are operated by a single inverter, protection cannot be provided by the electronic thermal relay function. Operation selection mitsubishi e700 inverter manual power failure Parameter 6.
Page Useful functions Parameter Main circuit capacitor life display Pr. Page Monitor display and mitsuvishi output signals Parameter Cumulative energizing power monitor and clear Pr. NOTE For the continuity test of the control circuit, use a mitsubishi e700 inverter manual high resistance range and do not use the megger or buzzer.
FR-E EC 2 – Page Page – Magnitude of frequency change setting P Reset Method Of Protective Function Reset method of protective function Troubleshooting Reset method of protective function Eliminate the cause of the error before you reset the inverter. Removal and reinstallation of the front cover Installation 2.
Mitsubisui Of Frequency Change Setting pr. Stall prevention is activated due to a heavy Setting 22 too large may result in frequent over- load. Page Since the Pr.