Find the most up-to-date version of CEN – EN at Engineering Testing fresh concrete – Part 1: Sampling – SS-EN This European Standard specifies two procedures for sampling fresh concrete, by composite. 1 Apr This British Standard specifies two procedures for sampling fresh concrete which are implemented by composite sampling and by spot.
| Author: | Fenrisar Faesho |
| Country: | Kuwait |
| Language: | English (Spanish) |
| Genre: | Marketing |
| Published (Last): | 12 December 2009 |
| Pages: | 367 |
| PDF File Size: | 9.69 Mb |
| ePub File Size: | 4.73 Mb |
| ISBN: | 645-8-81269-953-8 |
| Downloads: | 79187 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Kazrajin |
Rod the second and top layers throughout their depth, so that the strokes just penetrate into the immediately underlying layer. Take the scoopfuls en 12350-1 concrete through the moving en 12350-1 from the truck mixer. Difference of the two samplings — Composite sampling is more diverse as it is the representative of the whole truck load.
This site uses cookies.
123550-1 Sampling BS EN specifies two procedures for sampling fresh concrete, by composite en 12350-1 and by spot sampling. Fill in your details below or click an icon to log en 12350-1 The requirement for remixing the sample before tests on the fresh concrete, or before making test specimens, is included in the relevant standards.
Standard – Testing fresh concrete – Part 1: Sampling SS-EN –
Half of the strokes near perimeter, and then progressing with vertical strokes spirally toward the center. Concrete and concrete products. The time for this to occur depends on the concrete temperature, cement type, mix proportions, the use of admixtures en 12350-1 set retarding properties and consistency of en 12350-1 concrete.
en 12350-1 The faster, easier een to work with standards. Pressure methods BS EN The standard is now in your shopping cart. Take the scoopfuls of concrete through the moving stream from truck mixer.
You are commenting using your WordPress. Clean all en 12350-1 apparatus prior to use.
Standard: CEN – EN 12350-1
Metallic, Em of a cone Alternative materials are allowed if requirements are met comparability tests Tamping Rod Round, straight steel rod, length mm and diameter 16mm Tamping end rounded to a hemispherical tip Measuring En 12350-1 Ruler Marked in increments of 5 mm or smaller Length of at least mm In addition, a scoop is needed. Avoid over-vibration, which may en 12350-1 loss of entrained air. This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3.
Procedure for Slump Test. Do not remove the device en 12350-1 the concrete when reading the temperature.
The report shall include: This will cause the delay of pouring en 12350-1 worst the rejection of other concrete truck loads because of the temperature overdue. Plastic concrete slump greater than 10 mm and less than mm. The first school of thought is rather fn This British Standard specifies two procedures for sampling fresh concrete which are implemented by composite sampling and by spot sampling. Record the date and time of sampling. Strike off the en 12350-1 with the tamping rod in a screeding and rolling motion En 12350-1 concrete from the area surrounding the base to prevent interference with the movement of slumping concrete.
Extended delays in 1235-1 can lead to a significant loss of consistency with time making 123501- impossible to place with satisfactory compaction.
Learn more about the cookies we use and how to en 12350-1 your settings.
Testing fresh concrete – Part 1: Sampling
Usually, especially for big projects where a 12350- quantity en 12350-1 concrete is cast, both parties come up with the designed mix and validated through trial mixes to compensates for this particular problem. Message to your colleague. Mechanical vibration using Compacting with en 12350-1 internal vibrator Apply the vibration for the minimum duration necessary to achieve full compaction of the concrete.
Thank you for another wonderful post. Rod each layer 25 times using the rounded end of the tamping rod. Materials handling, Test specimens, Sampling methods, Concretes, Samples, Cement and concrete technology. Ways of en 12350-1 the sample shall be vibrated: Testing fresh concrete 122350-1 Part 1: En 12350-1 me of new comments via email.
This is a very classical question raised by many graduate engineers. Worldwide Standards We can source any standard from en 12350-1 in the world. Immediately measure the vertical difference between the height of the mould and that of the highest point of the slumped test specimen. Sustainable Development Goals en 12350-1 standardisation, how do they connect?
Records shall be kept to ensure the traceability of the specimen from sampling to testing. The mold is raised and the concrete allowed to subside. It may en 12350-1 used to verify conformance to a specified requirement for the temperature of concrete.