Service Manual, Elna DE Details. Elna Model DE Serger Machine Service Manual, 20 Pages. The physical copy of the instruction manual is a soft cover. Full text of “Elna Serger Instruction Manual dse de e” IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic. Hi there, Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this.
|Published (Last):||25 May 2018|
|PDF File Size:||17.45 Mb|
|ePub File Size:||6.76 Mb|
|Price:||Free* [*Free Regsitration Required]|
Pass the thread through the open slot of the take-up lever cover D and down to the guides E and F.
This helps to prevent sheer and lightweight fabrics from puckering. Bring the lower looper to its right position by turning the flywheel by hand. By using the 2-thread convertor on the upper looper, 2-thread flatlock will be available Model Pull the knob d first to the right, and then swing it down. Remove mnual screw cap and loosen the screw so that side cover can be taken off.
Full text of “Elna Serger Instruction Manual dse de e”
Pay close attention when the machine is used by 614dee hear children. Tighten the needle tension so that the lower looper thread is completely rolled down to the underside of the fabric.
Jan 09, Elna Sewing Machines. Next pull the needle thread gently and bring the knots to the front of the needles. These numbers are located on the specification plate.
Loosen the needle clamp screws a with the Allen screwdriver bto remove the old needles.
ELNA 614DE Manuals
Remove the needle you are not using the same as for 3-thread use and the upper thread from the machine. Open the front door. Sew on a scrap of fabric and adjust the tensions according to the illustration, depending on mannual desired finish.
A balanced tension a – b The needle threads lie on the top side of the fabric just like a row of normal straight stitches on the upper looper thread, and just visible in the lower looper thread on the underside of the fabric. Douglas Plant Level 2 Expert Answers. The fixed blade is made of a special alloy and will rarely need to be replaced.
A manual for elna 614DE – Elna Sewing Machines
First release Model or loosen the tensions, then pull the looper threads gently behind the needle mankal the knots have passed through. Add Your Answer Tips for a great answer: The email address entered is already associated to an account. Turn the cutting width dial upwards to increase the width, or downwards to decrease it. The final appearance can be enhanced by using a heavy decorative thread suitable for overlock use in the looper s.
Unlock the moving blade, refit the side cover and screw cap. Elma lower the presser foot swing the lever c up. To unplug, grasp the plug not the cord. Fold the fabric along the line to be topstitched and sew over the folded edge.
However, when the differential feed control slide c is set at 1. Dec 31, Elna Sewing Machines.
Sewing Edge-to-Edge Align the edges of the two pieces of fabric, with their wrong sides facing each other, and proceed in a similar manner as above. To change the cutting width, bring the needle bar to the highest position.
Draw the thread down between the two tension discs of the yellow tension control, then through the other thread guides and the hole in the upper looper, steps C to G. The tension settings for the 2-thread overcast are different from those of 3- thread use.
V Stitch Length Most overlook sewing projects can be done with the stitch length set at 2 to 3. To re-engage the moving blade, push the moving blade release lever to the right and turn it towards the back, then release the lever.
Elna DE Manuals
For sewing fluffy or fairly thick fabric, the extra lift 614ed mm will be available by swinging the lever c down again. How can this be resolved. A balanced tension d The needle thread lies flat and straight, to the left, and locks with the lower looper thread on the top side of the fabric and as a flat V-shape on the underside. Threading the Lower Looper – Coloured green on the chart and on the thread guides.