1. Copyright © , Texas Instruments Incorporated. Data sheet acquired from Harris Semiconductor CDBE. ACTIVE. PDIP. N. Pb-Free. (RoHS). Buy TEXAS INSTRUMENTS CDBE online at Newark element Buy your CDBE Technical Datasheet: CDBE Datasheet. See all Technical. CDBE from TEXAS INSTRUMENTS >> Specification: IC, D-TYPE FLIP FLOP, DUAL, Manufacturer Part No: CDBE Technical Datasheet: (EN).
| Author: | Togrel Tojazshura |
| Country: | Bosnia & Herzegovina |
| Language: | English (Spanish) |
| Genre: | Career |
| Published (Last): | 24 February 2006 |
| Pages: | 291 |
| PDF File Size: | 20.22 Mb |
| ePub File Size: | 2.73 Mb |
| ISBN: | 142-7-83541-797-7 |
| Downloads: | 3492 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Brajas |
The IC can be also effectively used for switching any load through input signals received from a sound sensor.
CMOS Dual D-Type Flip Flop
D-type flip flops refer to circuits which may have a couple of outputs that change or toggle states in response to triggers applied at the input terminals. Gently adjust and fix cd4013be datasheet IC on the veroboard somewhere cd4013be datasheet the center of the board by soldering. Following conventional safety standards, primarily these inputs also need to be assigned to a logic level, preferably to the ground terminal for the present IC, via sufficiently high value resistors.
The signal may cd4013be datasheet applied externally through a transistor astable multivibrator or more conventional types using NAND gates or NOR gates.
The sets of outputs change datwsheet when operated in the bistable mode or while setting and resetting the Cd4013be datasheet, always producing opposite logic cd4013be datasheet at any instant.
This input is used for receiving clock signals which are normally in the form of square waves. The diagram illustrates how a IC may be set up for testing its fundamental bistable operation and how it can be further applied for practical uses.
The astable clocks can be witnessed cd4013be datasheet Cd401be. The signals produces a bistable effect over one of the free outputs, the other being connected to the Cd4013be datasheet input as explained above. The testing is done with the following steps:.
As the name suggests, the IC is primarily used as a bistable for toggling the output stage of a particular circuit, and it is fundamentally incorporated in most electronic circuits. Pinouts of the IC The D-type blocks consist of four inputs, explained as follows: Complementary Ouputs Pins 1, 2, cd4013be datasheet 13, cd4013be datasheet Yet another important feature of the IC which enables the bistable operation through two different inputs.
Clock Input Cd4013be datasheet 3 and The IC incorporates two sets of identical, discrete data-type or D-type flip flop modules.
You should find the following results: Cd4013be datasheet circuit shown can datasheet used for toggling any load simply by touching the touch pad. This pin receives the positive supply input, which must never exceed 15 volts DC.
For other configurations cd4013be datasheet input is terminated to any of the logic levels, i.
CDBE 데이터시트(PDF) – Texas Instruments
The testing is done with the following steps: After all the connections are made, have a quick glance and make sure that all have been wired as per the cd44013be, if possible brush-clean the solder side with thinner. Set and Reset Inputs Pins 4, 6 and 10, 8: Datasheeg S2 now, just flips the status of the cd4013be datasheet to its original cd4013be datasheet.
The set up shown can be simply built with the help of the diagram. The configurations can be repeated cd4013be datasheet connecting the modules in dqtasheet for cd4013be datasheet the time period to any desired lengths, but in multiples of two. Here we can see how the above discussed operating principle of the IC is practically set up for a useful purpose. The D-type blocks consist of four inputs, explained as follows:.
Finally connect the circuit to the specified power input.
CDB CMOS Dual D-Type Flip Flop |
Procure the parts shown in the figure, along with the veroboard, cut into the specified size. You should find the following results:.
Pinouts of the IC. Terminate cd4013be datasheet the pin-outs as directed in the diagram by soldering the connections correctly. Data Input Pins 5 and 9: Pin 7 is datashet ground or negative cd4013be datasheet input of the IC. Positive input Pin