3 Feb This standard is issued under the fixed designation D; the 1 This test method is under the jurisdiction of ASTM Committee D18 on Soil. ASTM D Standard Test Method for Electronic. Friction Cone and Piezocone Penetration Testing of. Soils. Recently updated standard describing. 1 Jan ASTM D Standard Test Method for Electronic Friction Cone and Piezocone Penetration Testing of Soils. standard by ASTM.
|Published (Last):||27 October 2015|
|PDF File Size:||11.75 Mb|
|ePub File Size:||4.34 Mb|
|Price:||Free* [*Free Regsitration Required]|
However, many of the procedural requirements herein could apply to those penetrometers.
Note 3-The quality of the astm d5778 produced by this standard is dependent on the competence of the personal performing the test, and the suitability of the equipment and facilities used. Are you sure you want astm d5778 unsubscribe monitoring?
The astm d5778 stated in each system are not equivalents; therefore, each system must be used independently of the other. The use of an inclinometer is astm d5778 recommended since asrm will d578 information on potentially damaging situations during the sounding process. Pore pressure dissipation, after a push, can also be monitored for correlation to soil compressibility and permeability.
Notes are optional and private. Reliable results depend on many factors and Practice D provides a means of evaluating some of those factors. The printed version is available at half price when you buy the electronic version. Cone tip projected area is commonly referred to in square centimetres for convenience. Engineers may obtain soil samples from parallel borings astm d5778 correlation purposes but prior information or experience may preclude the need for borings.
Users of this astm d5778 are cautioned that compliance with Practice D does not in itself assure reliable results. Du abonnerer allerede dette emne. Reliable results depend on many factors and Practice D provides a means of evaluating some of those factors.
Link to Active This link will always route to the current Active version of the standard. Astm d5778 various data reported should be displayed in mutually compatible units as agreed to by the client or user.
Link to Active This link will always route to the current Active version of astm d5778 standard.
Within Section 13 on Calculations, SI units are considered the standard. The geotechnical application of asgm electronic cone penetrometer test is discussed in detail in Test Method Dhowever, the use Field tests using mechanical-type penetrometers are covered elsewhere by Test Method D Other commonly used units such as the inch-pound system are shown in brackets. The interpretation of asstm results from this test method provides estimates of the types of soil penetrated.
There is a problem adding monitoring – please try again later There is a problem adding the astm d5778 – please try again later. Username or astm d5778 invalid.
Do not astm d5778 this again. You have successfully saved to your supplier list.
Note 3—The quality of the results produced by this standard is dependent on the competence of the personal performing the test, and the suitability of the equipment and facilities used. This method tests the soil in-situ and soil samples are not obtained.
However, many of the procedural astm d5778 herein could apply to astm d5778 penetrometers. Register or Log in for direct access to additional content.
International Standards for CPT – Gouda Geo-Equipment BV
Other commonly used units such as the inch-pound system astm d5778 shown in brackets. Kontakt venligst Dansk Standard. Activation of monitoring failed – please try again astm d5778 or contact astm d5778. Other commonly used units such as the inch-pound system are shown in brackets. For typical gamma-ray spectrometry systems and sample Field tests using mechanical-type penetrometers are covered elsewhere by Test Method D Continue shopping Proceed to checkout. This test method provides data used for estimating engineering properties of soil intended to help with the design and construction of earthworks, the foundations for structures, and the behavior of soils under astm d5778 and dynamic loads.
However, many of the procedural requirements herein could apply to those penetrometers. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Within Section 13 on Calculations, SI metric units are considered the standard. Historical Version s – view previous versions of standard.
When properly performed at suitable sites, the test provides a rapid means for determining subsurface conditions.