Buy ASTM D Standard Test Method for Consolidated Undrained Triaxial Compression Test for Cohesive Soils from SAI Global. Consolidated Undrained Triaxial Compression Test for Cohesive Soil. 15 Jan ASTM D Standard Test Method for Consolidated Undrained Triaxial Compression Test for Cohesive Soils. standard by ASTM.
|Published (Last):||23 August 2015|
|PDF File Size:||15.84 Mb|
|ePub File Size:||4.23 Mb|
|Price:||Free* [*Free Regsitration Required]|
In addition, they are representative of the significant digits that generally should be retained. Three or six simple thumbscrew are used to clamp the upper part of the cell to the base, which make assembly and disassembly a very quick and Standard triaxial cells and accessories The cell essentially consists of a transparent polycarbonate chamber which has a piston assembly fit to the top and a double flange base fit to the bottom.
Data acquisition is included in the load frame; four channels xstm available for load, displacement, pore pressure and volume change. It is beyond the scope of this test method to consider significant digits used in analysis methods for engineering design. Users of this test method are cautioned that compliance with Practice D does not ensure reliable testing.
ASTM D, Test equipment Controls
Home Products Search results Results for: In d47767 standard density is given only in SI units. Introduced by the company over 50 years ago, they have undergone continuous development and are the ideal solution for advanced and research laboratories that want to perform high A typical standard triaxial system with external data acquisition system includes: The design of the cell ensure vertical alignement of the cell ram by clamping the Perspex wall separately from Soil mechanics – Dynamic triaxial systems: Data acquisition can be shared with other soil testing equipment.
Note 1—If the strength is required for the case where the soil is not consolidated during testing prior to shear, refer to Test Method D or Test Method D The shear strength of a saturated soil in triaxial compression depends on the stresses applied, time of consolidation, strain rate, and the stress history experienced by the soil.
Triaxial cell with accessories: Standard triaxial configuration with built-in data acquisition can be used for performing asfm tests such as CBR, Unconfined and CRS. Installed on a PC communicating x4767 the system over a fast Ethernet connection, the software can be used to configure the system scalibrate transducers, specify test parameters, set Please contact us for a complete offer. Soil mechanics – Static triaxial systems: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D Standard
Link to Active This link will always route to the current Active version of the standard. Standard triaxial configuration with external data acquisition can be used for performing additional test such as CBR, Unconfined and CRS, Permeability.
In this test method, the shear characteristics are measured awtm undrained conditions and is applicable to field conditions where soils that have been fully consolidated under one set of stresses are subjected to a change in stress without time for further consolidation to take place undrained condition d476, and the field stress conditions are similar to those in the test method.
It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
The shear strength determined from the test expressed in terms of total stresses undrained conditions or effective stresses drained conditions is commonly used in embankment stability analyses, earth pressure calculations, and foundation design. This shear strength may be applied to field conditions where full drainage can occur drained conditions or where pore pressures induced by loading can be estimated, and the field stress conditions are similar to those in the test method.
Reliable testing depends on several factors; Practice D provides a means of evaluating some of those factors.
With this equipment it is possible d47667 perform the consolidation stage of three triaxial specimens at the same time for CU and CD tests in anisotropic conditions. TRITECH original high-performance load frames for triaxial tests, ideal solution for advanced and research laboratories that want to perform high quality tests at.
Active Risk Management
EmS technology is environmentally friendly and clean to operate, requiring aatm compressed air or hydraulic oil. The precision of this test method is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used.
Soil mechanics – Triaxial load frames: The inch-pound units given in parentheses are mathematical conversions which are provided for information purposes only and are not considered standard. Generally, three specimens are tested at different effective consolidation stresses to define a strength envelope.