This specification2 relates to possible hazards that may not be recognized readily by the public and that may be encountered in the normal use for which a. ASTM F available in Chinese here: COMPS/htm. – Both F‐07e1 and F‐08 can be included as a. Both F ASTM F (PF) – Designation: F – 08 An American National Standard Standard Consumer Saf.
|Published (Last):||6 December 2007|
|PDF File Size:||4.80 Mb|
|ePub File Size:||2.28 Mb|
|Price:||Free* [*Free Regsitration Required]|
FHSA shall conform to the labeling requirement of that act. A force of 15 lbf 67 N shall be applied evenly within 5 s and maintained for an additional aatm s. A procedure for testing the? The load shall be applied gradually over a 5-s period and then shall be maintained for 10 s.
A relief valve shall be so arranged that the pump will not generate a positive or negative pressure of more than 2 psig. This specification does not cover product performance or quality, except as related to safety. Points of nails or fasteners shall not protrude so as to be accessible. If the circuit protection device automatically resets, continue the stalled motor test until the battery is exhausted.
ASTM F963-11 Toy Safety Testing
For circular holes, also 9f63-08 the requirement under 4. The disk shall be attached to an appropriate compression scale having an accuracy of The required tensile force shall be applied evenly, within a period of 5 s, parallel to the major axis of the test component, and maintained for an additional 10 s. Make sure that the radiated sound is not affected by the grip of the hand.
F — 08 operation. The relevant tests for a type of toy can be performed in any order except where speci?
Yo-Yo Elastic Tether Toys: Folding Mechanisms and Hinges: One way to determine if a child can sit ast, a product is to verify that the seat width would accommodate the hip breadth of a child in the age range for which the product is intended. The requirements for the assembled toy do not apply to toys where the assembling makes up a signi? Labeling statements for balloons are contained in 5.
Wheels, Tires, and Axles.
These requirements are applicable before and after use and abuse testing in accordance with Section 8. The ventilation areas shall consist of a f936-08 of two holes, with a total of at least 2 in. Short-circuit parts of opposite polarity.
Maintain the 11 Testing is to be conducted while the vehicle is operated on a hard level surface covered with 3M General Purpose Safety Walk tape or equivalent surface with a coefficient of friction between 1. For testing purposes, any textile fabrics used in toys should comply with 16 CFR Stand side-face with the microphone and keep the rattle at the same height as the microphone at a distance of 50 cm.
Operate the vehicle in the mode that results in the maximum continuous current draw.
If the toy shuts off automatically after an operating time of greater than 30 s, continue the test until the toy shuts off. Handles or hinges connected to the toy made with pliable material straps and ropes will be considered exempt. Teethers and Teething Toys.
This specification does not cover product performance or quality, except as related to safety. The table top should be large enough such that, with the toy resting on and fully over the table top, the side of the measurement box from which the measurement is being made is also above the table top see 8.
In addition, no advertising copy or graphics shall state or imply that the child will be safe with such a toy if left unsupervised. Revisions account for incidents of ingestion due to magnetic components that were small parts of a toy and to reflect the age of children involved in d incidents. Holes, Clearance, and Accessibility of Mechanisms Criteria for determining which toys are subject to these requirements are provided, in part, in 16 CFR Historical Version s – view previous versions of standard.
After being subjected to the use and abuse tests of 8. Design Guidelines for Battery Operated Toys. The gauge shall be oriented such that the 2. Additionally, the protective tip shall not produce or reveal hazardous points or edges when?
Except for the labeling requirements pointing out the functional hazards and age range for which the toy is intended, this specification has no requirements for those aspects of a toy that present an inherent and recognized hazard as part of the function of the toy.
Stroller and Carriage Toys. With the exception of products such as paper punch-out games and similar items, any toy or game that is intended for use by children who are at least three years old 36 months but less than six years of age 72 months and includes a small part is subject to the labeling requirements in accordance with 5.
There are no force requirements for double action locking devices. Strike downwards ten times with hard lashes in a slow tempo.
ASTM F – 17 Standard Consumer Safety Specification for Toy Safety
Metal wires or other metal materials used for stiffening or for retention of form in toys shall not fracture to produce a hazardous point, edge, or projection hazard when tested in accordance with 8.
The tests shall be conducted in an expected use environment. Drape the charger, cable, and battery with a double layer of cheesecloth. This standard does not purport to address all of the safety concerns, if any, associated with its use. Pull the elastic material to aetm right side so that the hook of the force gauge is adjacent to the left upper hook and parallel to the right bottom hook without exceeding a force adtm 5.
Corners f63-08 structures do not fall under this category. The content of soluble elements in the extract is determined.